If you have been prescribed Trimix, or you are considering it, two questions matter more than any other: how much do I inject and how do I inject it correctly? This page answers both, step by step: the injection technique, the dosage chart and typical ranges, how often you can use it, how long it lasts and how to store it. It also covers what to do if the dose is too weak or too strong and when to call your provider.
One rule first: Trimix is prescription-only and your prescriber sets your dose. The numbers on this page are the typical ranges prescribers work within. They are not your dose. Your starting dose, your formula and your limits come from the provider who reviewed your health and they can change as you and your provider find what works for you.
This page gives general information and typical ranges. It is not a prescription. Your prescriber sets your dose and your formula. Never change your dose on your own.
How to Inject Trimix: Step by Step
A Trimix injection, sometimes called a Trimix shot, is injected directly into the penis, into the spongy tissue (the corpora cavernosa) on either side. The needle is very fine and most men say it hurts far less than they expected. The whole process takes a few minutes once you have done it a few times.
Before you start: wash your hands. Lay out everything you need: your vial of Trimix, a syringe and needle, an alcohol wipe and a sharps container for the used needle. Check the vial label: the formula, your dose and the beyond-use date. Do not use a vial past its beyond-use date and do not use a vial that was left warm when it should have been kept cold, ask your pharmacy if you are unsure.
Step 1: Prepare the dose. Draw air into the syringe equal to your dose, push it into the vial, then draw up your prescribed amount of Trimix. Hold the syringe upright and tap out any air bubbles. Your prescriber will have shown you this, if you were not shown, ask before your first home injection.
Step 2: Choose the site. Inject into the side of the shaft, at the 10 o'clock or 2 o'clock position, on either the left or the right side. Alternate sides each time. Do not inject into the top (where nerves and blood vessels run), the underside (where the urethra is), or the head of the penis. Do not inject into a vein you can see, or into an area that is bruised, scarred, or sore from the last injection.
Step 3: Clean and inject. Wipe the injection site with an alcohol wipe and let it dry. Hold the penis gently stretched out to the side. Push the needle in at a right angle, straight in, until it is fully in the tissue. Inject the Trimix slowly and steadily, then pull the needle straight out.
Step 4: Apply pressure. Press the injection site firmly with the alcohol wipe or a clean gauze for a few minutes. This reduces bruising and bleeding. Do not massage the area hard. Put the used needle straight into your sharps container, never recap it with your fingers and never reuse a needle.
Step 5: Wait. An erection usually begins within 5 to 20 minutes. Plan for that window, inject shortly before sex, not hours ahead. If no erection happens, do not inject again the same day. Tell your provider; the usual answer is a small dose increase next time, not a second injection.
How to inject Trimix correctly, in short: right tissue, right position, right angle, slow injection, firm pressure afterwards and alternate sides. Most first-try failures are technique, not dose, if your first injection did not work, check your technique with your provider before assuming the dose was wrong.
Prepare the dose
Choose the site
Clean the skin
Inject slowly at a right angle
Apply pressure
Using a Trimix Auto Injector
Some men use an auto injector, a spring-loaded device that pushes the needle in for you at the press of a button. It does the same injection, just with a steadier, faster needle entry and many men find it easier and less painful than injecting by hand. The dose, the site and the preparation are exactly the same; only the needle insertion is automatic. If you are nervous about pushing the needle in yourself, ask your provider whether an auto injector is an option for you.
How to Use Trimix: The Basics in One Place
How to use Trimix comes down to a short routine: keep the vial cold as labelled, prepare only your prescribed dose, inject into the side of the shaft at 10 or 2 o'clock, alternate sides, apply pressure, dispose of the needle safely and wait 5 to 20 minutes. Do not inject more than your prescriber allows, never inject twice in one day and wait at least 24 hours between doses, your prescriber will confirm the exact limits for you.